TECHNICAL SPECIFICATIONS 30 cm LED LAMP Production of Iran’s Nobarpart Industrial Company

General Specifications A complete optical set consists of 3 green, yellow and red modules that can be supplied with the lantern either fully or individually. To change the luminaires to the LEDs, if you do not want to replace the lantern, you can only replace the LED modules with the luminaires ‘luminaire luminaire system that was produced at Iran’s NoPPP. LED modules are designed to be interchangeable with the luminaires’ It is a production company of the company. All parts of the lantern are entirely of high quality polycarbonate materials, specially designed for guidance lights and highly resistant to uv and acid rain. The size of the luminaire body is approximately 355 × 350 mm, with a lens diameter of about 300 The millimeter has a range of 280 ± 5. In the case of a full-mask lantern, a full mask with a diameter of 330 ± 530 mm in diameter and 300 ± 5 mm in the lighthouse connection at a depth of 215 ± 5 is connected to the body with a screw on the luminaire. In the case of half-masked lighthouse with a height of 5 ± 185 mm outside and 230 ± 5 ° at the point of attachment to the lighthouse at a depth of 215 ± 5 °, which is attached to the body by a screw on the body. The hinge is secured to the body and has a plastic bar for sealing. – The LED modulus of the parts The following polymer has been formed: – Casing (body) of the primary polycarbonate material for specialty headlamps – lens of the primary polycarbonate Lens for LED and power supply should be trusted completely screwed in the casing and the lens is completely sealed installed on it. The lens also protects the light and the angle of light from possible water and dust and / or moisture entering the electronic set. LEDs are traffic-sensitive, life-saving, 000/100 hours special for traffic lights and traffic signals of the type One (Grad A) comes directly from the manufacturer. The green type is the mcd8000 and the yellow type is mcd5500 and the red is 6000 mcd and is limited to the color spectrum permitted for the traffic light. – All parts are easily open, closed and replaced if necessary. .- All moving parts that can penetrate the water or dust into the lamp have reactive gaskets. He does not have the possibility of entering water and dust into the lamp, while ensuring the strength of the installation. – All dimensions and specifications are in accordance with the European standard (AS2144). – Lighthouse bases of the PC .The mounting rings and their connection area to the lantern body with precision molding provide the possibility of accurate adjustment (5 degrees) in the vertical axis to provide the best performance in a completely sturdy and non-interchangeable manner, and after installation no stress Bending or torsion does not apply to the lamp. – The lanterns are capable of installing the back plate. – Lanterns and modules They are made of recyclable polymer materials and do not pollute the environment. – On all the main parts of the calendar of production, the raw material, the name of the company Novarbartar is carved. – The lights are modular and can be installed on each other from one to four buildings – The flashing light used in the lamp has a design suitable for switching off at peak voltage, and has high quality electronic components and a heat sink suitable for continuous operation. The flashing range can be changed easily. It is possible to switch between 50 and 60 times per minute and have a dual-symmetric dual-channel luminaires. Three houses. – The quality and performance of the entire lantern and LED is guaranteed for one year and has been designed and lashed for a minimum of 5 years. Technical Specifications: Operating Temperature: 70 to + 30 ° C. Input Voltage: 170-265 mm. Input Voltage: 40 mm. (Possible Thin Cables Available on the Market.) Power Consumption (10 ± 10 Watts) Independent of Lightning Intensity. Input Voltage Up to 95% (0.95 < PF) Distortion of current consumption less than 14% (14%> THD) Change of light source due to dimming from 30% to 100% Continuously protecting the input voltage shock and protecting over temperature when the delay time on and off is less than 100 milli Secondary filter eliminates high frequency noise and transient shocks (such as lightning) in the light input of the PWM method and, consequently, the static color spectrum Renewal of a torque of up to 300 V When one of the LEDs is burned, only 2 of them are turned off and the remaining LEDs remain constant. It works without flickering and shaking the light even in unstable power supply systems, using the latest switching power supply with high power factor and as a result The use of the very smallest parts and the destruction of the much less use of LEDs for long life and light intensity, and 30-degree angles, employing a special design of the printed circuit, which reduces the temperature and, as a result, increases the useful life. The minimum results are obtained for protective tests (rounded and Must and Water), which are in accordance with standard I The EC529 is implemented for the LED module IP 65 and for the IP 54 lantern.